Electric Skateboard Tips

Maximizing Your Electric Skateboard Lifespan: 7 Maintenance Tips

Electric Skateboard

Whether you're a beginner or a pro, electric skateboards are a prevalent mode of transportation. But like anything else, they can eventually show signs of wear and tear. If you take care of your board, it will take care of you.

In this blog post, we will provide easy maintenance tips for your electric skateboard so that you can keep it running smoothly for years to come. From fixing wheel bearings to cleaning the deck and more, read on to learn everything you need to know to keep your board in top condition.

1. Clean the deck and bearings once a month

After every use, clean the deck and bearings with a soft cloth or vacuum cleaner. Be sure to remove all of the debris! Cleaning the deck and bearings of an electric skateboard is an important part of maintaining the performance and lifespan of your skateboard. Here are the general steps for cleaning the deck and bearings:

  1. Remove the wheels: To clean the bearings, you will need to remove the wheels from the skateboard. Depending on your skateboard, you may need a special tool or be able to do it by hand.
  2. Clean the bearings: Once the wheels are removed, you can access the bearings. Use a bearing cleaner or rubbing alcohol to clean the bearings. You can also use a toothbrush or a small brush to scrub away dirt or grime.
  3. Dry the bearings: After cleaning the bearings, make sure to dry them thoroughly. You can use a cloth or a blow dryer to remove any excess moisture.
  4. Lubricate the bearings: Once the bearings are clean and dry, you can apply a small amount of bearing lubricant to each bearing. Be sure to follow the manufacturer's instructions for the proper amount of lubricant to use.
  5. Reassemble the wheels: Once the bearings are clean and lubricated, you can reassemble the wheels by replacing them wheels onto the skateboard.
  6. Clean the deck: To clean the deck of the skateboard, you can use a mild cleaner or water and a cloth to wipe down the surface. Remove any dirt or grime from the deck to keep it in good condition.
  7. Dry the deck: After cleaning the deck, make sure to dry it thoroughly to prevent any water from seeping into the bearings or other parts of the skateboard.
  8. Store the skateboard: Once the skateboard is clean and dry, you can store it safely until you are ready to ride it again.
electric skateboard

2. Don't ride in rain or snow

If it's raining or snowing, avoid riding your board outdoors. Not only will it be slippery, but you could also get caught in a storm and lose your board or worse. If you have to ride in these conditions, bring an extra set of clothes and shoes just in case something goes wrong. 

There are a few reasons why it is not recommended to ride an electric skateboard in rain or snow:

  1. Safety concerns: Riding an electric skateboard in wet conditions can be dangerous due to the increased risk of slipping or falling. Wet surfaces can be slippery, making it more difficult to control the skateboard and maintain balance.
  2. Damage to the skateboard: Wet conditions can also cause damage to the skateboard itself. Water can seep into the bearings, motors, and other skateboard components, causing them to rust or malfunction.
  3. Reduced performance: Electric skateboards are not designed to perform optimally in wet conditions. The damp surface may cause the wheels to lose traction, which can reduce the speed and performance of the skateboard.
  4. Shortened battery life: Riding an electric skateboard in wet conditions can also shorten the battery life of the skateboard. The motors may need to work harder to maintain traction, which can drain the battery more quickly.

3. Check the screws that connect the trucks to the board

One of the most common problems skateboarders encounter is loose screws connecting the trucks to the board. The trucks can move around when this happens, making it challenging to ride. Today we'll show you how to check the screws and fix them if they're loose.

To check the screws that connect the trucks to the board on an electric skateboard, you will need to follow these steps:

  1. Remove the wheels: To access the screws that connect the trucks to the board, you will need to remove the wheels from the skateboard. Depending on your skateboard, you may need a special tool, or you may be able to do it by hand.
  2. Inspect the screws: Once the wheels are removed, you will be able to see the screws that connect the trucks to the board. Inspect the screws to ensure they are appropriately tightened and not loose or damaged. And you need to locate each screw that connects the truck to the board. Look for signs of wear or damage, and adjust as needed. If all of the screws are tight, you can skip to step four. If one or more of the screws are loose, tighten them using a wrench or adjustable wrench. Be sure to use a bit of caution when tightening, as over-tightening may cause damage to your board.
  3. Tighten the screws if needed: If you notice that any of the screws are loose, you can use a screwdriver to tighten them. Tighten the screws evenly to ensure that the trucks are balanced and secure.
  4. Check for any damage: In addition to checking the tightness of the screws, you should also look for any signs of damage or wear on the screws or the trucks. If you notice any damage, you may need to replace the screws or the trucks.
  5. Reassemble the skateboard: Once you have checked the screws and made any necessary repairs or adjustments, you can reassemble the skateboard by replacing the wheels. Make sure that the screws are tight before testing your skateboard. If everything is okay, you can move on to step five. If there are still any problems, you may need to have your skateboard professionally repaired.
  6. Test the skateboard: After reassembling the skateboard, it is a good idea to test it to make sure that it is working properly. Take a short ride to ensure that the trucks are secure and that the skateboard is stable.

4. Replace the skateboard pads every few months

Skateboard pads are one of the most important parts of your board and should be replaced at least every three months. Over time, the pads will wear down and can cause your board to become unstable. 

It is recommended to replace the skateboard pads on an electric skateboard every few months for a few reasons:

  1. Wear and tear: Skateboard pads are subject to wear and tear from regular use, and over time they may become worn down or damaged. Replacing the pads regularly can help to ensure that the skateboard is in good condition and performing optimally.
  2. Improved performance: New skateboard pads can provide better grip and traction, which can improve the performance of the skateboard. This is especially important for electric skateboards, as they often require a strong grip to maintain control and stability.
  3. Safety: Worn or damaged skateboard pads can increase the risk of slipping or falling while riding the skateboard. By replacing the pads regularly, you can help to ensure that your skateboard is safe to ride.
  4. Aesthetics: Replacing the skateboard pads can also give your skateboard a fresh, new look. This can be especially appealing if the old pads are dirty or discolored.

Overall, replacing the skateboard pads every few months is a good way to maintain the performance, safety, and appearance of your electric skateboard.

5. Check your battery and charger regularly

Electric skateboards rely on electric skateboard batteries and electric skateboard chargers to power the board and the rider. Make sure your battery is properly maintained by checking it regularly and charging it when needed for these reasons.

  1. Performance: Properly maintaining the battery and charger can help to ensure that your electric skateboard is performing optimally. Checking the battery and charger regularly can help you to identify any issues or problems that may affect the performance of the skateboard.
  2. Safety: Failing to properly maintain the battery and charger can increase the risk of accidents or injuries while riding the skateboard. Regularly checking the battery and charger can help to ensure that the skateboard is safe to ride.
  3. Longevity: Properly maintaining the battery and charger can help to extend the lifespan of your electric skateboard. By ensuring that the battery and charger are in good working order, you can help to avoid costly repairs or replacements in the future.
  4. Convenience: Regularly checking the battery and charger can also help to avoid any unexpected issues or inconveniences while riding the skateboard. For example, if the battery is low or the charger is not working properly, you may be unable to use the skateboard when you need it.
electric skateboard

To check your battery and charger when using an electric skateboard, you will need to follow these steps:

  1. Check the battery level: The first step in checking your battery is to determine the current level of charge. Most electric skateboards have a battery indicator that shows the current charge level, or you can use the skateboard's app or software to check the battery level.
  2. Charge the battery if needed: If the battery is low, you will need to charge it before you can use the skateboard. Plug the charger into a power outlet and connect it to the skateboard's battery. Follow the manufacturer's instructions for the proper charging time and procedure.
  3. Check the charger: Once the battery is charged, you should also check the charger to ensure that it is working properly. If the charger is not working, you may need to replace it.
  4. Check the battery connections: If the battery is charged and the charger is working properly, you should also check the connections between the battery and the skateboard. Make sure that the connections are secure and free of any dirt or debris.
  5. Test the skateboard: After checking the battery and charger, you should test the skateboard to make sure it is working properly. Take a short ride to ensure that the skateboard is functioning correctly and that the battery is holding a charge.

By following these steps, you can ensure that your battery and charger are in good working order and that your electric skateboard is ready to ride. If you encountered charging issues, you can troubleshoot the problem through this blog.

6. Store your electric skateboard securely

Electric skateboards are a fun way to get around, but like any electronic device they can be vulnerable to damage if not taken care of. Here are some tips for keeping your electric skateboard in good shape:

  • Store your electric skateboard properly. Make sure it's upright and that the wheels are properly attached.
  • Keep the board clean. Use a damp cloth to wipe down the deck and grip tape.
  • Protect the battery pack. Keep it away from metal objects and don't drop it or hit it hard.
  • Protect the charger. Don't place it near heat or direct sunlight.

7. Adjusting Your Wheels

Electric skateboards are great for getting around town, but like any piece of technology, they can need some occasional TLC.

If you are using JKING all terrain electric skateboard, you should use our all terrain wheels or cloud wheel power kit.

To adjust the wheels on an electric skateboard, you will need to follow these steps:

  1. Remove the wheels: To adjust the wheels, you will need to remove them from the skateboard. Depending on your skateboard, you may need a special tool or you may be able to do it by hand.
  2. Adjust the height of the wheels: The height of the wheels can be adjusted by turning the kingpin nut on the truck. To raise the wheels, you will need to loosen the kingpin nut and adjust the trucks accordingly. To lower the wheels, you will need to tighten the kingpin nut.
  3. Adjust the tightness of the wheels: The tightness of the wheels can be adjusted by turning the axle nuts on the truck. To make the wheels tighter, you will need to tighten the axle nuts. To make the wheels looser, you will need to loosen the axle nuts.
  4. Reassemble the skateboard: Once you have made the necessary adjustments to the wheels, you can reassemble the skateboard by replacing the wheels.
  5. Test the skateboard: After reassembling the skateboard, it is a good idea to test it to make sure that the wheels are adjusted properly. Take a short ride to ensure that the skateboard is stable and that the wheels are turning smoothly.
electric skateboard

By following these steps, you can adjust the wheels on your electric skateboard to suit your riding style and preferences. Whether you want to increase the stability of the skateboard by raising the wheels, or you want a smoother ride by making the wheels looser, adjusting the wheels can help you customize the performance of your skateboard.

Just be sure to follow the manufacturer's instructions and use caution when making any adjustments to the wheels, as improper adjustment can affect the performance and safety of the skateboard.

Conclusion

Keep your electric skateboard in top shape with these 7 easy maintenance tips. From cleaning and lubricating the bearings to checking the battery and charger, these simple steps can help you maintain the performance, safety, and longevity of your skateboard.

As a professional electric skateboard manufacturer and avid enthusiast, Jking will give you the most professional advice

Jking electric skateboard

Reading next

electric skateboard
electric skateboard

Leave a comment

All comments are moderated before being published.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Free shipping

Tell your customers about your shipping offer.

Customer service

Tell your customers how they can reach you.

Refer a friend

Tell your customers about your promotional offers.

Secure payment

Tel your customers about your payment methods.